How to make do-it-yourself drinking bowls for rabbits

How to make do-it-yourself drinking bowls for rabbits
How to make do-it-yourself drinking bowls for rabbits

How to make do-it-yourself drinking bowls for rabbits
How to make do-it-yourself drinking bowls for rabbits

For raising rabbits, it is necessary to have well-equipped rabbits with feeders and drinking bowls, thanks to which caring for animals will become much easier. When making a do-it-yourself aviary for animals, you should take into account the area that is necessary for each family of rabbits.

Drinking bowls for rabbits are made from any container that is at hand. To do this, it is enough to be smart and make equipment that will continuously supply water to rabbits in the required quantity. For example, ordinary plastic bottles that should be correctly positioned in the rabbitry and put on nipple drinkers for rabbits. This device will work perfectly, but it should be noted that this creature can nibble them and the liquid that spills will simply spill out. Do-it-yourself drinking bowls for rabbits are easy to do, but when installing in rabbitry, you should pay attention to the location. Water containers must be installed so that the rabbits only reach out to the nipple drinkers. If the height of the rabbitry does not allow this installation, then a casing should be made that will protect against damage to the water tank.

In order to water living creatures with water, you can use the usual container, which must be installed on a horizontal surface in rabbitry. This method is quite simple, but not considered effective, because rabbits constantly overturn such a container and spill water from it.

It is necessary to consider in more detail how nipple drinkers with a fence are made. In the calculation should take two 1.5 liters. plastic containers on which covers with nipple drinkers will be wound. The box should be spacious, so it should be made 40 cm high and 30 cm wide. The most suitable material is a polished board 20 mm thick. The width of the box should be 15cm and when buying lumber, this size must be taken into account. Side racks should carry 40cm x 15cm, the lower and upper bridge is 36cm x 15cm. The rear wall is 40cm x 40cm and two front doors are 40cm x 20cm each. Assembly is carried out using metal corners, which are located on the joints. The rear panel is mounted on wooden beams with a thickness of 20mm x 30mm. When installing the doors, you can use any hinges, but the most suitable will be the piano awnings. When assembling the entire structure, it is necessary to use 32 wood screws, with a cross head. Next, two plastic containers are installed in such a way that their necks look down. Drinkers are fastened using clamps that are located on two sides of each container. That is, each nipple drinker for rabbits is attracted from below and from above to the back of the box. For each container, two clamps are required that are bolted together. In this case, the lower bar must have two openings through which the neck of the bottles will go out. Subsequently, it is necessary to screw on them lids with nipple drinkers, which are essentially nipple drinkers.

Read more:  Do-it-yourself drinkers for rabbits

Any nipple drinker is much better than a regular water tank. For example, you need to leave for a long time, but animals cannot be left without water. Pouring water into the nipple drinker, you can be sure that animals can drink water at any time if necessary. As for the ordinary bowl, there is no hope for it, because the rabbit can accidentally turn it over, thereby dooming itself to thirst.

Simple drinkers for rabbits can be made of metal sheets, while creating them any shape and capacity, but you should return to the nipple drinkers and consider their advantages. For example, with a large number of rabbits, it is necessary to improve the supply of water and this can be done as follows. To begin with, it should be understood that to carry out the idea you should purchase a flat tank that can be mounted on the wall. Suppose a tank holds 10 liters of water and is heavy in weight. In this case, the brackets are driven into the wall, on which the water tank is mounted. Now you need to decide how many drinkers are required. For example, 10 pieces will be enough. Ten holes are drilled in the lower part of the tank and adapters are installed, on which plastic hoses should be put on. Further, they are diverted to different places and attached to the walls, after which nipple drinkers are put on their ends.

When making nipple drinkers, the number of rabbits should be considered, because each living creature requires a certain amount of liquid. Water consumption depends on the time of year, and in the hot summer period they need water every two hours.